d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 1 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 lead (pb)-bearing thick film chip resistors with cecc approval, available with established reliability features ? iecq-cecc approved to en 14040 1-802, version e, with established reliability, failure rate level e6 ? iecq-cecc approved to en 14040 1-802, version a, without failure rate level ? snpb termination plating on ni barrier, minimum 10 % pb ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 applications ? military ?avionics ? industrial notes ? specifications given for a produc t description ending en802 .. a pply likewise to both product versions, th e version a, who se description ends with en802 e0 and the version e, whose description ends with en802 e6. ? these resistors do not feature a limited lifetime when operated within the permissible limits. however, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifeti me. note ? failure rate level e6 (10 -6 /h, q = 0.3), equivalent to mil level p, is superior to level e5 (10 -5 /h, q = 1) and thus can be used as a replacement. technical specifications description d12 en802 .. d25 en802 .. imperial size 0805 1206 metric size code (en/cecc style) rr2012m rr3216m resistance range 1 ?to 1 m ; 0 resistance tolerance 5 %, 1 % temperature coefficient 200 ppm/k, 100 ppm/k, 50 ppm/k rated dissipation, p 70 0.125?w 0.25?w operating voltage, u max. ac rms or dc 150?v 200 v permissible film temperature, ? f max. 125 c operating temperature range -55 c to 125 c max. resistance change at p 70 for resistance, | r / r | max. after: 1 % tolerance products: 10 ?to 1 m 1000?h 1 % 8000?h 2 % insulation resistance 1 g permissible voltage against ambient (insulation): 1 min; u ins 200?v 300?v technical specifications for version a description d12 en802 e0 d25 en802 e0 nominal failure rate level e0 quality factor, q 3 failure rate, fit observed < 0.1 x 10 -9 /h technical specifications for version e description d12 en802 e6 d25 en802 e6 assessed failure rate level e6 = 10 -6 /h quality factor, q 0.3 failure rate, fit observed < 0.1 x 10 -9 /h
d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 2 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) other tcr or tolerances, or combinations thereof, or resistance values from other e-series than given are not permitted in en 1 40401-802 for version e products. (2) the temperature coefficient of resistance (tcr) is not specified for 0 jumpers. temperature coefficient and resistance range type / size tcr tolerance resistance e-series d12 en802 e0 200 ppm/k 5 % 1 to 1 m e24 100 ppm/k 1 % 10 to 1 m e24; e96 50 ppm/k 1 % 100 to 1 m e24; e96 jumper (2) ; i max. = 1.5 a 20 m 0 - d12 en802 e6 (1) 200 ppm/k 5 % 1 to 9.1 e24 100 ppm/k 1 % 10 to 1 m e96 50 ppm/k 1 % 100 to 1 m e96 jumper (2) ; i max. = 1.5 a 20 m 0 - d25 en802 e0 200 ppm/k 5 % 1 to 1 m e24 100 ppm/k 1 % 10 to 1 m e24; e96 50 ppm/k 1 % 100 to 1 m e24; e96 jumper (2) ; i max. = 2 a 20 m 0 - d25 en802 e6 (1) 200 ppm/k 5 % 1 to 9.1 e24 100 ppm/k 1 % 10 to 1 m e96 50 ppm/k 1 % 100 to 1 m e96 jumper (2) ; i max. = 2 a 20 m 0 - packaging type / size code quantity packaging style width pitch packaging dimensions d12 en802 e6 p1 1000 paper tape acc. iec 60286-3, type 1a, on reel 8 mm 4 mm ? 180 mm / 7" d12 en802 .. p5 5000 p0 10 000 ? 285 mm / 11 1 / 4 " d25 en802 e6 p1 1000 ? 180 mm / 7" d25 en802 .. p5 5000 p0 10 000 ? 285 mm / 11 1 / 4 "
d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 3 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? the ordering information acco rding to en 140401-802: 2007 shown above succeeds an d replaces the ordering information according to earlier versions of the de tail specification en 140401-802 or its pr edecessor cecc 40401-802, for example: cecc 40401-802 ez rr2012m b 562r f e6 cecc 40401-802 s rr2012 b 562r f e6 with ez; s assessment level, where ez is successor to and superior replacement for s rr2012m; rr2012 style, with suffix m for metric b temperature coefficient, according to the detail specification a = 200 ppm/k; b = 100 ppm/k; c = 50 ppm/k part number and product description part number: d1208050b5620fp5e6 part number for zero ohm jumpers: d1208050000000p5e6 d1208050b5620fp5e6 d1208050000000p5e6 type / size version tcr resistance tolerance packaging special d120805 d251206 0 = neutral c = 50 ppm/k b = 100 ppm/k a = 200 ppm/k 0 = jumper 3 digit value 1 digit multiplier multiplier 8 = *10 -2 9 = *10 -1 0 = *10 0 1 = *10 1 2 = *10 2 3 = *10 3 4 = *10 4 0000 = jumper f = 1 % j = 5 % 0 = jumper p1 p5 p0 en 140401-802 e6 en 140401-802 e0 product description: d12 100 562r 1 % p5 en802 e6 product description for zero ohm jumpers: d12 0r0 p5 en802 e6 d12 100 562r 1 % p5 en802 e6 d12 - 0r0 - p5 en802 e6 type / size tcr resistance tolerance packaging specification failure rate level d12 d25 50 ppm/k 100 ppm/k 200 ppm/k 10r = 10 562r = 562 10k = 10 k 1m = 1 m 0r0 = jumper 1 % 5 % p1 p5 p0 en 140401- 802 e6 e0 en 140401-802 ordering information example of the ordering information for a resistor: d12 100 562r 1 % en802 e6 en140401-802ezrr2012ms562rfe6 the elements used in the component number have the following meaning: en140401-802 en detail specification number ez assessment level for the zero-defect approach rr2012m style s temperature coefficient, according to en 60062 u = 200 ppm/k; s = 100 ppm/k; r = 50 ppm/k 562r resistance value, accordin g to en 60062, 4 characters f tolerance on rate d resistance, according to en 60062 j = 5 %; f = 1 % e6 failure rate level according to en 60115-1, table zb.1 for version a the nominal failure rate level is e0 please note that the en 140401-802 orderi ng information is not specific to the nature of the termination plating.
d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 4 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 description production follows a set of instructions established for reproducibility. a thick film layer and a glass-over are deposited on a high grade ceramic substrate (al 2 o 3 ) with its prepared inner co ntacts. the target value is achieved by laser cutting an l shaped groove in the resistive layer. the resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. the terminations receive a final snpb on nickel plating, controlled for a minimum lead content of 10 %. a four-character code marking designates the resistance value in accordance with iec 60062 (1) . the result of the determined production is verified by an extensive testing procedure performed on 100 % of the individual resistors. only acce pted products are placed into the paper tape according to iec 60286-3 (1) , type 1a . assembly the resistors are suitable fo r processing on automatic smd assembly systems. they are suitable for automatic soldering using wave, reflow or vapor phase as shown in iec 61760-1 (1) . solderability is specified for 2 years after production. the encapsulation is resistant to all cleaning solvents commonly used in the electro nics industry, including alcohols, esters and aqueous so lutions. the suitability of conformal coatings, potting compounds, and their processes, if applied, shall be qualified by appropriate means to ensure the long-te rm stability of the whole system. materials vishay acknowledges the following systems for the regulation of hazardous substances: ? iec 62474, material declaration for products of and for the electrotechnical industry, with the list of declarable substances given therein (2) ? the global automotive declarable substance list (gadsl) (3) ? the reach regulation (1907/2006/ec) and the related list of substances with very high concern (svhc) (4) for its supply chain except for the intentionall y added lead (pb) in the termination finish, the products do not contain any of the banned substances as per iec 62474, gadsl, or the svhc list, see www.vishay.com/how/leadfree . vishay pursues the elimination of conflict minerals from its supply chain, see the conflict minerals policy at www.vishay.com/doc?49037 . approvals the resistors are approved within the iecq-cecc quality assessment system for electronic components to the detail specification en 140 401-802 which refers to en 60115-1 , en 60115-8 and the variety of environmental test procedures of the iec 60068 (1) series. conformity is attested by the use of the cecc logo ( ) as the mark of conformity on the package label. the vishay draloric production facility is registered with the cage code sh903. related products a parallel family of lead (pb)-fre e thick film chip resistors with cecc approval, availa ble with establishe d reliability, is available, see datasheet: ? crcw.... en802 - thick film chip resistors with cecc approval, available with established reliability ( www.vishay.com/doc?28806 ) a wider range of product sizes, tcr, tolerance and resistance values, plus the option of values from a different e series is available without approval to any en specification (quality factor q = 10). see the datasheets: ? d/crcw e3 - standard th ick film chip resistors ( www.vishay.com/doc?20035 ) ? d/crcw - lead (pb)-beari ng thick film, rectangular chip resistors ( www.vishay.com/doc?20008 ) notes (1) the quoted iec standards are also released as en st andards with the same number and identical contents. (2) the iec 62474 list of declarable subs tances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474 . (3) the global automotive declarable substance list (gadsl) is maintained by the american chemistry council, and available at www.gadsl.org . (4) the svhc list is maintained by the european chemical agency (echa) and available at http://echa.europa.eu/candidate-list-table .
d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 5 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 functional performance 100 - 50 150 0.0 0.1 050 ambient temperature amb ? 0.2 0.3 70 d25 en802.. d12 en802.. 125 derating c power dissipation p w 100 0.1 1 1k 10k 10 100k d25 en802.. d12 en802.. resistance value r 1m v/v in accordance with iec 60195 current noise voltage ratio current noise voltage ratio 10 100 1k 10k resistance value r 1m db 100 80 60 40 100k d25 en802.. d12 en802.. in accordance with iec 60440 thir d harmonic ratio a 3 non-linearity - thir d harmonic ratio a 3
d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 6 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tests and requirements all tests are carried out in accordance with the following specifications: en 60115-1, generic specification en 60115-8 (successor of en 140400), sectional specification en 140401-802, detail specification iec 60068-2-xx (1) , test methods the parameters stated in the test procedures and requirements table are based on the required tests and permitted limits of en 140401-802. the table presents only the most important tests, for th e full test schedule refer to the documents listed above. however, some additional tests and a number of improvements against those minimum requirements have been included. the testing also covers most of the requirements specified by eia/eca-703 and jis-c-5201-1. the tests are carried out under standard atmospheric conditions in accordance with iec 60068-1 (1) , 4.5, whereupon the following values are applied: temperature: 15 c to 35 c relative humidity: 25 % to 75 % air pressure: 86 kpa to 106 kpa (860 mbar to 1060 mbar). a climatic category lct / uct / 56 is applied, defined by the lower category temperature (lct), the upper category temperature (uct), and the du ration of exposure in the damp heat, steady st ate test (56 days). the components are mounted for testing on printed-circuit boards in accordance with en 60115-8, 2.4.2, unless otherwise specified. test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change ( r ) stability class 1 or better stability class 2 or better stability for product types: 10 to 1 m 1.0 to 1 m d12 en802.. d25 en802.. 4.5 - resistance - 1 % 5 % 4.7 - voltage proof u =?1.4 x u ins ; 60 s no flashover or breakdown 4.13 - short time overload u ?= 2.5 x ?2?x u max. ; duration according to style d12: 1 s; d25: 2 s (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) 4.17 58 (td) solderability solder bath method; sn60pb40; non-activated flux (235? 5) c; (2? 0.2)?s good tinning ( 95 % covered); no visible damage 4.8 - temperature coefficient (20/- 55/20) c and (20/125/20) c 50 ppm/k; 100 ppm/k 200 ppm/k 4.32 21 (ue 3 ) shear (adhesion) 45 n no visible damage 4.33 21 (ue 1 ) substrate bending depth 2 mm, 3 times no visible damage; no open circuit in bent position (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) 4.19 14 (na) rapid change of temperature 30?min at - 55?c 30 min at 125 c 5 cycles (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) 1000?cycles (1 % r + 0.05 ) (1 % r + 0.05 ) p 70 x r
d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 7 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) the quoted iec standards are also released as en st andards with the same number and identical contents. 4.23 climatic sequence: (1 % r + 0.05 ) (2 % r + 0.1 ) 4.23.2 2 (bb) dry heat 125 c; 16?h 4.23.3 30 (db) damp heat, cyclic 55 c; 90 %?rh; 24?h; 1 cycle 4.23.4 1 (ab) cold - 55 c; 2?h 4.23.5 13 (m) low air pressure 1?kpa; (25? 10) c; 1?h 4.23.6 30 (db) damp heat, cyclic 55 c; 90 %?rh; 24 h; 5 cycles 4.23.7 - dc load u ?= ? u max. ; 1 min 4.25.1 - endurance at 70 c u ?= ? u max. ; 1.5 h on; 0.5 h off; 70 c; 1000 h (1 % r + 0.05 ) (2 % r + 0.1 ) 70?c; 8000 h (2 % r + 0.05 ) (4 % r + 0.1 ) 4.18 58 (td) resistance to soldering heat solder bath method; (260? 5)?c; ? (10? 1)?s (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) 4.35 - flammability, needle flame test iec?60695-11-5 (1) , 10 s no burning after 30 s 4.24 78 (cab) damp heat, steady state (40? 2) c (93 3) %?rh; 56 days (1 % r + 0.05 ) (2 % r + 0.1 ) 4.25.3 - endurance at upper category temperature 125 c; 1000 h (1 % r + 0.05 ) (2 % r + 0.1 ) 4.40 - electrostatic discharge (human body model) iec 61340-3-1 (1) 3 pos. + 3 neg. discharges; voltage acc. to style d12: 800 v; d25: 1000 v (1 % r + 0.05 ) 4.29 45 (xa) component solvent resistance isopropyl alcohol; 50 c; method 2 no visible damage 4.30 45 (xa) solvent resistance of marking isopropyl alcohol; 50 c; method 1, toothbrush marking legible, no visible damage 4.22 6 (fc) vibration, endurance by sweeping f = 10 hz to 2000 hz; x , y , z 1.5 mm; a 200 m/s 2 ; 10 sweeps per axis (0.25 % r + 0.05 ) (0.5 % r + 0.05 ) 4.39 - periodic electric overload u ?= ?2 x u max. ; 0.1 s on; 2.5 s off; 1000 cycles (1 % r + 0.05 ) 4.27 - single pulse high voltage overload; 10 s/700 s u ?= 10?x ?2 x u max. ; 10 pulses (1 % r + 0.05 ) test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change ( r ) stability class 1 or better stability class 2 or better stability for product types: 10 to 1 m 1.0 to 1 m d12 en802.. d25 en802.. p 70 x r p 70 x r 15 x p 70 x r p 70 x r
d.. en802 www.vishay.com vishay draloric revision: 01-sep-15 8 document number: 28808 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions notes ? the resistors are marked using the four-character code system of iec 60062 (1) on their black protective coating. (1) the quoted iec standards are also released as en st andards with the same number and identical contents. dimensions and mass type / size l (mm) w (mm) h (mm) t 1 (mm) t 2 (mm) mass (mg) d12 en802.. 2.00 0.15 1.25 0.15 0.5 0.15 0.40 0.20 0.40 0.20 5.5 d25 en802.. 3.20 0.15 1.60 0.15 0.5 0.15 0.50 0.25 0.50 0.25 10 recommended solder pad dimensions type / size wave soldering reflow soldering g (mm) y (mm) x (mm) z (mm) g (mm) y (mm) x (mm) z (mm) d12 en802.. 0.65 1.40 1.50 3.45 0.65 1.10 1.40 2.85 d25 en802.. 1.50 1.60 1.90 4.70 1.50 1.25 1.75 4.00 t 2 l w t 1 h g x y z
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
